My Account

Wish List (0)

Mega-IO Home Expansion Card for Raspberry Pi

Product Code:MMP-1254

Ex.Tax £25.00

Availability: 19

Mega-IO Home Expansion Card for Raspberry Pi
Mega-IO Home Expansion Card for Raspberry Pi
Questions3 Answers3 | Expand All
Hi, Do you also have the "RASPBERRY PI MegaIO-IND CARD FOR INDUSTRIAL AUTOMATION" Best regards, Olle
Olle Apelqvist
  • No, this product hasn't even been put into production yet -
    ModMyPi LTD
    Was this answer helpful? 0
Optical isolation?
How does this board isolate any 240v loads from the Pi? I am considering using it to switch small inductive loads (AC motorised valves, CH pumps and a contactor), with a total load on the board of c. 300 watts/
  • Your best bet is to contact the manufacturer
    ModMyPi LTD
    Was this answer helpful? 0
Does this include standoffs etc
Hello, Does this include the standoffs etc and header block for the connector for mounting to my pi? If not, what size is recommended?
Phil Davies
  • Yes, this comes with all stand offs and screws needed.

    The header that connects the board to the Pi is pre-soldered to this board.
    ModMyPi LTD
    Was this answer helpful? 0
Showing 1 to 3 of 3 (1 pages)

Sequent Microsystems MEGA-IO is a stackable expansion card for Raspberry Pi B+, 2, 3 and Zero/W. The Mega-IO is packed with useful input/output ports to help you expand physical hardware interfacing on the Rasberry Pi / Pi Zero.

Two of the Raspberry Pi’s GPIO pins are used for I2C communication. Another pin is allocated for the interrupt handler, leaving 23 GPIO pins available for the user.

Up to four MEGA-IO cards can be stacked on top of a Raspberry Pi. Any of the inputs of the MEGA-IO can be configured as interrupt inputs.

MEGA-IO adds the following I/O functions:

  • Eight on-board relays
  • Eight 12 bit A/D inputs
  • Eight optically isolated inputs
  • One 12 bit DAC Output
  • Four open collector outputs
  • Six GPIO's

Technical Specifications:

    • Operating voltage: 3.3V
    • CPU frequency: 16 MHz
    • Touch sensing capability
    • Max. input voltage on any pin: 4V
    • Series protection resistor on IO pins: 51 Ohms
    • Output Low Level Voltage on I/O pins: Max. 0.45V
    • Output High Level Voltage on I/O pins: Min. 2.6V
    • Driver: ULN2003F12FN-7
    • Output Low Voltage: 0.6V
    • Max Pull Up Voltage: 20V
    • Max sink per channel: 100mA @ 3.3V Logic Input
    • 140mA @ 5.0V Logic Input
    • ESD: 4kV HBM, 1kV CDM
  • EIGHT 12 bit ADC
    • Sample rate: Up to 1 Msps
    • Input low pass filter: 0.22µF/51 Ohms
    • LED current limit resistor: 1 Kohm
    • Input Forward Current: Typ. 5 mA, Max 50 mA
    • Input Reverse Voltage: 5V
    • Input Forward Voltage: 1.25V @ 10 mA
    • Isolation Resistance: Min 10 exp(12) Ohms
    • Isolation Voltage: Typ 10,000 V
    • Relay max current/voltage: 10A/25V
    • PCB max current/voltage: 2.5A/24V
    • 60 mA @ +5V (all relays off)
    • 800 mA @ 5V (all relays on)


User Guides

Write a review


Your Review

Note: HTML is not translated!


Bad           Good

are you happy?

please confirm the selections below are correct

The product is currently Out-of-Stock. Enter your email address below and we will notify you as soon as the product is available.