ModMyPi MCP23017 HAT - 32 Channel I/O Expansion HAT [Discontinued]

ModMyPiSKU: MMP-0619
Price:
Sale price £17
incl. VAT
excl. VAT

Compatible with:

Awesome Extras

The Pi HutMCP23017 Port Expander
Sale price £3 incl. VAT excl. VAT
Save 20%
ModMyPiModMyPi MCP23017 pHAT - 16 Channel I/O Expansion (Zero)
Sale price £8 Regular price £10 incl. VAT excl. VAT

The MCP23017 HAT from ModMyPi is the perfect I/O expansion HAT for your Raspberry Pi (any 40-pin version).

The HAT features two removable MCP23017 DIP IC's, which utilise two i2c pins (which can be shared with other devices if required), and in exchange gives your Raspberry Pi an additional 32 GPIO ports! Each I/O pin can be configured as an input, output or input with a pull-up resistor.

The MCP23017 HAT is stackable, featuring selectable i2c address jumpers which support up to 8 independent addresses: This means you can add up to 128 additional I/O's to a single Raspberry Pi by stacking up to 4 MCP23017 HATs!

The MCP23017 HAT can also be used to protect your Raspberry Pi! We've used removable, rather than surface mount, MCP23017 DIP IC's which can act as a replaceable buffer for the Raspberry Pi's GPIO, essentially protecting your Raspberry Pi from damage via the GPIO ports.

The MCP23017 HAT is powered via the Raspberry Pi's GPIO port, but features an included (but unsoldered) terminal block for advanced users wanting to use an external 5V source, or stack multiple MCP23017 HATS on a single Pi. The isolation jumper "PWR JUMPER" must be removed when using an external source.

The product comes fully assembled with our push-fit "plug & play" Single Shroud Header, Socket Header, and 14mm HAT Mounting Kit, so there's no soldering required, and you can get started in no time with our Wiki & Example Code!

Please Note. The external power terminal block is NOT soldered onto the board, and is designed for advanced users only.

Features

  • 2 x MCP23017 IC's
  • Removable & Replaceable DIP Packaged IC's - If you damage one, simply replace!
  • Selectable i2c Address Jumpers - Supports up to 8 Independent Addresses
  • 32 Port GPIO Expander Board with Configurable I/O's (Input/Ouput/Input w/ Pullup)
  • Jumper Isolated Terminal Block 5V Input
  • Stackable (Up for 4 MCP23017 HATs, and up to 128 I/O's)
  • HAT Compliant
  • MCP23017 HAT Kit Includes:
    • 1 x Fully Assembled MCP23017 HAT with 2 x MCP23017 IC's
    • 1 x Mounting Kit: 4 x M2.5 14mm F/F Stand-offs & 8 x M2.5 5mm Bolts
    • 1 x Push Fit 40 Pin Extra Tall Header
    • 1 x Unsoldered Two Point Screw Terminal Block
  • The MCP23017 Features:
    • 16 bit remote bidirectional I/O port
    • High speed I2C interface
    • Three hardware address pins to allow up to eight devices on the bus
    • Configurable interrupt output pins - active-high, active-low or open-drain
    • INTA and INTB can be configured to operate independently or together
    • Configurable interrupt source - based on input changes, so you don't need to keep polling the chip
    • Polarity Inversion register to configure the polarity of the input port data
    • External Reset input
    • Low standby current: 1?A max.
  • MCP23017 Specifications:
    • Bus Frequency: 1.7MHz
    • Chip Configuration: 16bit
    • IC Interface Type: I2C, Serial
    • Interface Case Style: DIP
    • No. of I/O's: 16
    • No. of Pins: 28
    • Supply Voltage Max: 5.5V
    • Supply Voltage Min: 1.8V

Downloads

MCP23017 HAT Wiki w/ Hardware & Software Installation & Examples

Example Code

Payment & Accreditations

Payment methods
Visa Mastercard Maestro PayPal Amazon Klarna

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

Accreditations