My Account

Wish List (0)

Saved Carts

Compare

Approved Re-Seller
Follow us on Facebook! Follow us on Twitter! Follow us on Instagram!

Sep 12, 2017

If you find your WiFi mouse acting very slow, or even "rubber banding", theres a simple fix! The Raspberry Pi's USB poll rate for mice has been set slightly on the slow side, which has been causing issues with WiFi mice. By increasing the poll...

Sep 01, 2017

A Raspberry Pi can talk! No, really! What is this magic we speak of? Well, the Raspberry Pi is not in fact, a tasty, fruity, delicious pastry, but a fully functioning computer the size of a credit card. Tastier still, some models can cost...

Aug 22, 2017

Use with the Raspberry Pi 3 and Zero W To get serial working over GPIOs 14 & 15 you have two options. Disable Bluetooth completely or move Bluetooth to the mini-UART. Disable Bluetooth If you don’t need to use Bluetooth the easiest...

Aug 22, 2017

If you want to detect an "output" with your Raspberry Pi, like a button being pressed or a motion sensor detecting movement, we can configure our Raspberry Pi's GPIO pin as an "input". That input pin can be in three states (known as Tri-State...

Aug 03, 2017

One of the features of our PiOT Relay Board is the ability to activate and deactivate it using a handshake pulse train. This is a neat little feature, however wouldn’t it be nice to know with confidence that when you’ve sent the pulse train that...

Aug 03, 2017

The TEMPer USB sensors are super easy to get setup on your Raspberry Pi thanks to a python library available on GitHub. https://github.com/padelt/temper-python Start by installing the required packages: sudo apt-get install python-usb...

Jul 21, 2017

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Raspberry Pi B+/2/3 Night Vision Camera 6x Acrylic Pieces 4x 1" M/F Stand Off 4x 1/4" F/F Stand...

Jul 20, 2017

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Raspberry Pi B+/2/3 IQaudIO Pi-Digi+ 6x Acrylic Pieces 4x M2.5 x 8mm M/F Stand Off 4x M2.5 x 25mm M/F...

Jul 20, 2017

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Raspberry Pi Zero / Zero W Allo BOSS Mini 6x Acrylic Pieces 4x M2.5 x 4mm M/F Stand Off 4x M2.5 x 18mm...

Jul 20, 2017

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Raspberry Pi B+/2/3 Allo BOSS 6x Acrylic Pieces 4x M2.5 x 8mm M/F Stand Off 4x M2.5 x 25mm M/F Stand...

Apr 13, 2017

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Raspberry Pi B+/2/3 PIco UPS 14x Black Acrylic Pieces 2x Clear Acrylic Pieces 4x M2.5 x 8mm M/F Stand...

Apr 13, 2017

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Raspberry Pi B+/2/3 PIco UPS 14x Black Acrylic Pieces 2x Clear Acrylic Pieces 4x M2.5 x 8mm M/F Stand...

Apr 07, 2017

In this project you will learn how to wire up a Photoelectric IR Through Beam Sensor (HC-89) and write some code to calculate the speed at which a motor is rotating. Things you will need: Raspberry Pi, Micro SD Card, Keyboard & Mouse,...

Mar 09, 2017

The mini-HDMI port on the Raspberry Pi Zero sits a few mm back from the edge of the case on the Official Raspberry Pi Zero Case. This means that some mini-HDMI cable will not seat correctly into the mini-HDMI port on the official case (depending...

Feb 22, 2017

In this project you will learn how to wire and program a passive infrared sensor. Things you will need: Raspberry Pi + SD Card Keyboard + Mouse Monitor + HDMI Cable Power Supply Breadboard 1x Red LED 1x Blue LED 2x 330Ω Resistor 5x...

Feb 22, 2017

In this project you will learn how to wire and program a light sensor and see how bright it is in your room. Things you will need: Raspberry Pi + SD Card Keyboard + Mouse Monitor + HDMI Cable Power Supply Breadboard 1x Red LED 1x Blue...

Feb 22, 2017

In this project you will learn how to wire and program a temperature sensor. Let’s see how hot the room is. Things you will need: Raspberry Pi + SD Card Keyboard + Mouse Monitor + HDMI Cable Power Supply Breadboard 1x Red LED 1x Blue...

Feb 21, 2017

In this project you will learn how to wire and program a buzzer. Let’s all make lots of annoying noises. This will be an SOS program Things you will need: Raspberry Pi + SD Card Keyboard + Mouse Monitor + HDMI Cable Power Supply

Feb 21, 2017

In this project you will controller either the red or blue led depending on what your chose. Things you will need: Raspberry Pi + SD Card Keyboard + Mouse Monitor + HDMI Cable Power Supply Breadboard 1x Red LED 1x Blue LED 2x 330Ω...

Feb 21, 2017

In this project you’ll learn how to make a LED blink! Things you will need: Raspberry Pi + SD Card Keyboard + Mouse Monitor + HDMI Cable Power Supply Breadboard 1x Red LED 1x Blue LED 2x 330Ω Resistor 1x M/M Jumper Wire 4x M/F...

Feb 21, 2017

In this project you’ll learn how to make a LED blink! Things you will need: Raspberry Pi + SD Card Keyboard + Mouse Monitor + HDMI Cable Power Supply Breadboard 1x Red LED 1x Blue LED 2x 330Ω Resistor 3x M/F Jumper...

Feb 21, 2017

In this project you’ll learn how to turn on and off a LED Things you will need: Raspberry Pi + SD Card Keyboard + Mouse Monitor + HDMI Cable Power Supply Breadboard 1x Red LED 1x Blue LED 2x 330Ω Resistor 3x M/F Jumper...

Feb 21, 2017

Run your first python program “hello world” Things you will need: Raspberry Pi + SD Card Keyboard + Mouse Monitor + HDMI Cable Power Supply Prerequisites: Latest version of Rasbian installed on your SD Card Raspberry Pi setup with...

Feb 14, 2017

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Raspberry Pi B+/2/3 Itead GSM Breakout Board 8x Acrylic Pieces 4x M2.5 x 8mm M/F Stand Off 4x M2.5 x...

Feb 10, 2017

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Raspberry Pi B+/2/3 Adafruit 16x2 LCD Kit 7x Acrylic Pieces 4x M2.5 x 8mm M/F Stand Off 4x M2.5 x 5mm...

Jan 30, 2017

Thanks to the FlightAware project you can now transform your Raspberry Pi into an aircraft tracking ADS-B groundstation! Our FlightAware Raspberry Pi Kit can be installed anywhere and receive real-time data directly from airplanes within 100 -...

Jan 19, 2017

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Raspberry Pi Zero 6x Red Acrylic Pieces 8x M2.5 x 4mm M/F Stand Offs 4x M2.5 x 16mm F/F Stand Offs 8x...

Jan 19, 2017

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Raspberry Pi B+/2/3 6x Red Acrylic Pieces 4x M2.5 x 18mm M/F Stand Offs 4x M2.5 x 8mm M/F Stand...

Jan 19, 2017

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Raspberry Pi B+/2/3 6x Red Acrylic Pieces 4x M2.5 x 18mm M/F Stand Offs 4x M2.5 x 8mm M/F Stand...

Nov 30, 2016

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Raspberry Pi B+/2/3 8x Black Acrylic Pieces 2x Clear Acrylic Pieces 4x M3 Screws 4x M3 Nuts NOTE:...

Oct 27, 2016

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Raspberry Pi Zero Raspberry Pi Camera PIR Motion Sensor 3x F/F Jumper Wires 7x black matte acrylic...

Oct 18, 2016

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Raspberry Pi Zero Half Size Breadboard 6x Acrylic Pieces 6x M3 Nylon Screws 6x M3 Nuts/li> NOTE:...

Oct 06, 2016

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Raspberry Pi B+ / 2 / 3 Grove Pi 4x M2.5 x 8mm M/F Stand Off 6x M2.5 Screw 2x M2.5 Nut 2x M2.5 x...

Sep 28, 2016

Motors are awesome. They are the fundamental components to any robot, be it as a servo motor, stepper motor or just your bog standard DC motor. 9 times out of 10, you’ll be using DC motors for the movement of your robot as they are super easy to...

Sep 22, 2016

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Raspberry Pi B+ / 2 / 3 Raspberry Pi Camera 6x black matte acrylic plates 1x thin clear acrylic...

Sep 06, 2016

Hooking up your UBEC to your Raspberry Pi really couldn't be easier. Simply plug in the 3 pin socket to your Raspberry Pi's GPIO header; pins 2,4 and 6, making sure the black wire of the UBEC is connected to pin 6. Now all you need to...

Sep 01, 2016

In this simple tutorial we will be showing you how to wire up your rotary encoder and how to use some python code to interact with it. Lets start with a brief explination of what a rotary encoder is, and how they work! A rotary encoder is a...

Aug 23, 2016

Introduction The Raspberry Pi is a great device with a load of I/O’s; but sometimes it’s just not enough! If you need more I/O's than the Pi can deliver, then there are a number of IC’s that you can use to expand the number of I/O’s available....

Aug 23, 2016

In this tutorial we will show you how to connect your Raspberry Pi to a 3G network using the Itead Raspberry Pi GSM Board (SIM800). This breakout board communicates to the Pi over serial, but as we know the serial ports of the Pi are initally...

Aug 17, 2016

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Raspberry Pi B+ / 2 / 3 9x Acrylic plates 4x M2.5 x 18mm M/F Stand Off 4x M2.5 x 16mm F/F Stand Off 4x...

Aug 09, 2016

Raspberry Pi Plant Pot Moisture Sensor via Analogue Signals Introduction Before we step into this tutorial, it’ll be good to have a small understanding of the difference between analogue and digital signals. Both types of signals can be...

Aug 08, 2016

This tutorial is aimed at those who are looking to use our micro USB WiFi dongle with their Raspberry Pi Zero. You need some way of setting up a WiFi connection without the dongle being plugged in, as you'll need to have your keyboard/mouse...

Aug 08, 2016

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials ModMyPi PiOT Relay Board 7x Acrylic plates 3x M2.5 x 25mm F/F Stand Off 3x M2.5 x 25mm M/F Stand...

Aug 08, 2016

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials ModMyPi PiOT Relay Board 6x Acrylic plates 3x M2.5 x 25mm F/F Stand Off 4x M2.5 x 8mm M/F Stand Off 7x...

Aug 08, 2016

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Pine64 2Gb 9x Acrylic plates 4x M3 x 25mm Bolt 4x M3 Nut NOTE: Acrylic is a hard and stiff plastic...

Aug 05, 2016

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Genuino 101 9x Acrylic plates 7x M3 x 25mm Bolt 7x M3 Nut 3x M3 x 5mm stand off 1x Adhesive PCB...

Jun 28, 2016

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Raspberry Pi Zero Raspberry Pi Camera Module Magentic Lens (optional) - Fisheye, Super Fisheye, Telephoto,...

Jun 28, 2016

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Genuino MKR1000 7x Acrylic plates 4x M3 x 25mm Bolt 4x M3 Nut NOTE: Acrylic is a hard and stiff...

Jun 21, 2016

This tutorial will show you the process of installing NOOBs on to a SD card, ready for you to plug into your Pi and to select an Operating System. The following steps were performed on a Windows computer. The steps may vary if you are using...

Jun 16, 2016

Waveshare 10.1" Screen Assembly Guide In the waveshare kit you'll received the following items: Screen (pre-assembled in acrylic) Acrylic mounting sheet Screen controller board Ribbon cable HDMI cable USB to micro USB...

Jun 16, 2016

So you've just received your Zero Delay Arcade USB Encoder and its time to wire it up! Start by getting the USB Encoder PCB board and take note of the connections. We are going to wire up the Joystick first, so grab that and the...

May 26, 2016

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Raspberry Pi B+/2/3 Pi-DigiAMP+ Full-HD Class D Amplifier 6x Acrylic plates 4x 25mm M/F hex...

May 24, 2016

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Genuino Micro (not included) 5x Acrylic Plates 4x M3 x 25mm Nylon Bolt 4x M3 Nylon...

May 23, 2016

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Genuino Mega (not included) 8x Acrylic Plates 8x M3 x 25mm Nylon Bolt 8x M3 Nylon Nut 4x M3 x 5mm...

May 23, 2016

PLEASE NOTE. THESE INSTRUCTIONS ARE FOR THE UPS PICO HV2.0 NOT THE NEWER RASPBERRY PI 3 VERSION UPS PICO HV3.0 - THE LATEST INSTRUCTIONS, FIRMWARE AND SCRIPTS ARE ALL AVAILABLE ON THE UPS PICO WIKI HERE. NEWER UPS PICO'S MAY BECOME DAMAGED WHEN...

May 20, 2016

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Genuino Zero (not included) 8x Acrylic Plates 7x M3 x 25mm Nylon Bolt 7x M3 Nylon Nut 3x M3 x 5mm...

May 20, 2016

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Genuino Uno (not included) 8x Acrylic Plates 7x M3 x 25mm Nylon Bolt 7x M3 Nylon Nut 3x M3 x 5mm Nylon...

May 09, 2016

If you've purchased our amazing Media Centre Kit, plugged it all in, powered it up, you might find it boots straight into the Raspbian operating system. Fear not, its super easy to get a media centre OS installed! Simply follow this step-by-step...

Apr 20, 2016

This tutorial will show you how to set a static IP address on your Pi with the release of Raspbian Jessie. At the time of writing, the latest release date of Raspbian Jessie is 18-03-2016 with Kernal version 4.1. I recommend doing this on a...

Apr 18, 2016

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Before assembly, please make sure nothing is plugged into the Raspberry Pi and that the SD card has been removed. Bill of...

Feb 09, 2016

In one of the recent Raspbian updates they have changed the orientation of the LCD output and touch coordinates. This could be a problem for you if you purchased a case and stand that has a fixed orientation. Fear not! It's really easy to flip it...

Jan 28, 2016

So you've got your Pi Zero, but you don't have an HDMI monitor! Argh!?! Right? Nope! The Pi Zero has a composite video out port which is very easy to access, and we're going to show you how! You'll need a few bits and pieces, including a...

Jan 07, 2016

Start by inserting the micro SD card into the dedicated micro SD card slot on the Raspberry Pi. This is located on the underside of the Pi. If you need an internet connection, plug in your Ethernet cable. (Optional) Then plug in...

Dec 23, 2015

Today, we’ll be showing you how to use a moisture sensor and a Raspberry Pi to send you an email notification when your plant needs watering! Very useful if you're forgetful of your houseplants, but of course can be expanded exponentially for...

Dec 21, 2015

The advent of the Pi Zero has brought the world of Raspberry Pi into the realm of wareable technology. It's time to throw off the shackles of your micro USB wall charger, and start powering using batteries. So, grab your nearest soldering iron,...

Dec 14, 2015

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Raspberry Pi Zero 5x Acrylic Plates 4x M2.5 12mm Nylon Screws 4x M2.5 Nylon Nuts NOTE: Acrylic is a...

Nov 22, 2015

PLEASE NOTE. THESE INSTRUCTIONS ARE FOR THE UPS PICO HV2.0 NOT THE NEWER RASPBERRY PI 3 VERSION UPS PICO HV3.0 - THE LATEST INSTRUCTIONS, FIRMWARE AND SCRIPTS ARE ALL AVAILABLE ON THE UPS PICO WIKI HERE. NEWER UPS PICO'S MAY BECOME DAMAGED WHEN...

Nov 20, 2015

Back in March 2012, one man, by the name Jacob Marsh, had a vision. That vision was to ensure the safety and wellbeing of every Raspberry Pi. Starting small, he designed and manufactured one of the first cases to market. Move forward 3 and a half...

Nov 18, 2015

Before we assemble the touch screen, we need to make sure that our Raspberry Pi has the latest version of Raspbian, and that all the software is up to date. Hook up your Pi to a monitor, plug in your keyboard and mouse and boot your Pi into...

Nov 10, 2015

Here's a little tutorial on how to setup an IR Receiver on OpenELEC/Kodi in side one of our Head Case's Activate Device Tree Overlay First we need to edit our config.txt file. To do this, we need to make the flash directory writable:

Sep 30, 2015

Raspbian Jessie is here! Find out more information about the update here - https://www.raspberrypi.org/blog/raspbian-jessie-is-here With the launch of Raspbian Jessie there is one significate difference users are going to notice, and that’s...

Sep 18, 2015

This tutorial assumes you are using an up-to-date Raspbian install, have access to either LXTerminal or SSH and have an internet connection! We're going to go through the steps on how to use a GPS module with your Raspberry Pi! In this...

Sep 18, 2015

At ModMyPi we offer a range of different micro-development boards, which all require slightly different power sources! Some are very stringent in their required input; for example, the latest Raspberry Pi recommends 5V @ 2A as a minimum for...

Sep 18, 2015

At ModMyPi we offer a range of different micro-development boards, which all require slightly different power sources! Some are very stringent in their required input; for example, the latest Raspberry Pi recommends 5V @ 2A as a minimum for...

Sep 18, 2015

At ModMyPi we offer a range of different micro-development boards, which all require slightly different power sources! Some are very stringent in their required input; for example, the latest Raspberry Pi recommends 5V @ 2A as a minimum for...

Sep 08, 2015

This is a very easy one - You only require a sharp knife and a printer (and preferably a cutting sheet)! Please ask before you ruin your kitchen side :) The custom artwork fits between the top clear panel, and the 2nd matte black panel. You...

Sep 04, 2015

So you've got a Raspberry Pi, but the USB output current isn't driving what you need it too? One of the newer features on the Raspberry Pi B+ and Raspberry Pi 2 Model B is improved power management. By default, the 4 USB ports on the Raspberry...

Sep 04, 2015

So you’ve got a shiny new touchscreen for your raspberry pi but are a little miffed that you still need to plug a keyboard in to be able to type… Well after this tutorial there will be no need! We will assume you have installed Raspbian and...

Sep 02, 2015

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Raspberry Pi A+/B+/2 Raspberry Pi 7" Touchscreen Display 12x Acrylic Plates 6x M3 20mm Screws 6x M3...

Sep 02, 2015

Bill of Materials 1x PCB 2x 10mm LED 4x Resistors 1x 10k ohm 1x 100 ohm 1x 10 ohm 1x 27 ohm 1x 2N7000 Transistor 1x 3x1 0.1” pin header 3x F/F Jumper Wires 3x 1” hex aluminium standoffs 3x ¼”...

Aug 31, 2015

You can now transform your Raspberry Pi into an all-in-one retro gaming console! Thanks to the RetroPie project you can play a multitude of old console games, such a SNES, NES, SEGA Mega Drive, Atari and many more on your Raspberry Pi.  At...

Aug 31, 2015

So you've got your shiny new Raspberry Pi and want to try loading a "3rd party" or BETA operating system (OS) that aren't supported by the standard NOOBs installation. NOOBs is the Raspberry Pi Foundations New Out Of Box OS that has a small...

Aug 31, 2015

Whether you're overclocking your Pi, running it in a hot environment or just want your Pi to look awesome, our high quality Raspberry Pi heat sink kits can help to reduce the operating temperature of the Raspberry Pi's SoC and LAN chip, and...

Aug 25, 2015

Introduction In this tutorial we’re going to go through how to use a voltage regulator within a circuit! Voltage regulators are designed to maintain and stabilise voltage levels. Regulators are found in most electronic devices, and can be...

Aug 18, 2015

Most SD cards are shockproof, waterproof, bulletproof and explosion-proof, and will likely survive Armageddon. However, somehow we manage to corrupt SD cards via the Raspberry Pi on a weekly basis! Nine times out of ten a simple reformat using...

Aug 10, 2015

Buttons and switches are the bread and butter of physical computing. Through the reaction speed game kit, we're going to (hopefully!) teach you some basic electronics using switches & resistors, and the basics of physical operation coding with...

Jul 14, 2015

Got your little zebra-turtle, and need to know how to assemble it? Well, just follow the pictures below! All acrylic comes with a protective layer, which must be peeled off before assembly!

Jun 19, 2015

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Raspberry Pi A+/B+/2 Pi-DAC+ Full-HD Audio Card 6x Acrylic plates 4x 25mm M/F hex stand-offs 4x 12mm F/F...

May 06, 2015

So you’ve come to the end of that film you were watching, not quite enough time for another, but still a little too early for bed… How about load up one of your favourite SNES games?! It’s super easy to setup your OpenELEC media centre to...

May 05, 2015

The laser-cut part of the camera box are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Raspberry Pi Model B Raspberry Pi Camera 6x black matte acrylic plates 3x thin clear acrylic...

May 01, 2015

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Raspberry Pi B+ / 2 / 3 Raspberry Pi Camera 6x black matte acrylic plates 1x thin clear acrylic...

May 01, 2015

The laser-cut part of the camera box are protected by an adhesive film which needs to be removed before assembly. Bill of Materials Raspberry Pi model A+ Raspberry Pi Camera 6x black matte acrylic plates 3x thin clear acrylic...

Apr 29, 2015

So you’ve got your camera setup with your Raspberry Pi, and you’ve got a PIR Infrared Motion Sensor and you’re thinking to yourself “There must be an easy way to start the camera recording when motion is detected?”… Well there is! Thanks to...

Mar 25, 2015

Bill of materials: 4x 1/4" OD Hex Standoffs (Male-Female) / 4-40 x 3/4" 4x 1/4" OD Hex Standoffs (Male-Female) / 4-40 x 3/8" 4x 1/4" OD Hex Standoffs (Female-Female) / 4-40 x 1/4" 4x 4-40 Hex Machine Screw Nuts 12x 4-40 x 1/4"...

Jan 30, 2015

With the release of yet another Raspberry Pi, we though it would be nice to show you they key difference between them all.     Raspberry Pi 2 Model B Raspberry Pi Model B+ Raspberry...

Jan 28, 2015

What you will need: 1x Raspberry Pi 2x External Hard Drives 1x USB Powered Hub We will assume you have Raspbian installed, and are fully up-to-date. So first thing to do is get all the hardware  plugged in and powered...

Jan 12, 2015

If you are experiencing drop outs on your wifi interent connection, it could be that your dongle is turning itself off after an idle period. To stop your wifi dongle doing this, we need to disable its power management. Either SSH to your Pi,...

Dec 09, 2014

Setting up the camera To enable the camera, at the command prompt enter: sudo raspi-config Then navigate to Enable Camera, Select Enable, Finish and finally Reboot. Taking a picture Taking a picture with a Raspberry Pi camera is...

Dec 09, 2014

This tutorial will show you how to make the reading of a sensor audible. In this example, we will be using the HC-SR04 Ultrasonic sensor, but it can be applied to most, if not all, other sensors. To do this, you will need to have the...

Oct 21, 2014

Wiring up the sensor First things first, let’s connect the sensor to the Raspberry Pi. Red wire connects to pin 1 Black wire connects to pin 6 Yellow wire connects to GPIO4 pin 7 (you can connect this wire to any of the GPIO pins,...